欧美成人福利一区二区三区-日本激情五月婷婷-国产一区精品成人-国产三级在线观看免费-欧美韩日国产在线-欧美黄色一级录影带-久久亚洲精品三区

Product Parameters

1. Realize high-frequency, fast, and frequent on-off of the circuit, with unlimited switching times.

2. The on-off process does not produce noise, there are no electric sparks, and there is no electromagnetic interference.

3. The service life is longer than that of commonly used electromagnetic relays.

4. Adopting dual MOS parallel active output, it has lower internal resistance, higher current, and strong power. At room temperature, it is 15A and 400W, which meets the needs of most devices.

5. It is often used to control motors, light bulbs, LED strips, DC motors, micro water pumps, solenoid valves, etc. Through this module, these devices can be easily controlled, which is very convenient.

6. Wide voltage operation (5-36V), most devices can be used, very convenient.

7. The interface is clear, simple, powerful, easy to understand, and almost meets all your needs.

8. There is a one button emergency stop function (STOP button), with reverse connection protection, and reverse connection does not burn.

9. Added sleep mode, which automatically turns off the monitor and wakes up with any button within 5 minutes without any operation.

10. Different OP, CL, and LOP parameters can be set, which are independent of each other and saved separately.

11. All settings have automatic power-off protection.

Product Functions

1. Working voltage: DC5V-36V

2. Trigger signal source: High level trigger (DC3.0V-24V) signal ground is not common with system ground to improve the anti-interference ability of the system (it can also be self short circuited to common ground)

3. Output capability: DC 5V-36V, continuous current 15A at room temperature, power 400W! Under auxiliary heat dissipation conditions, the maximum current can reach 30A

4. Static current: 15mA4

5. Service life: unlimited switch times

6. Working temperature:- 40~85°C

7. Size: 6.0 * 3.4 * 1.2cm

8. Equipped with optocoupler isolation to enhance anti-interference capability, industrial grade circuit board, set parameters for permanent memory after power failure

Timing range:

After setting the parameter values on the mode selection interface, short press the STOP key to select the timing range

XXX. The decimal point is in units, and the timing range is 1 second to 999 seconds

XX. The decimal point of X is in ten places, and the timing range is 0.1 seconds to 99.9 seconds

X. X.X. decimal point fully lit, timing range: 1 minute to 999 minutes

For example, if you want to set the OP to 3.2 seconds, move the decimal point to ten and the digital display will show 03.2.

Parameter description: OP conduction time, CL disconnection time, LOP cycle times (1-999 times, "--" represents infinite cycles).

These parameters are independent of each other, but they are shared among different modes. For example, in P1.1, the conduction time OP is set to 5 seconds. If the user wants to switch to P1.2 mode, when entering P1.2 to set the corresponding parameters, the OP will also be 5 seconds;

Short press the SET key on the main interface to display OPCL, LOP, and corresponding time XXX;

If there is only OP time in the mode (such as mode P1.1, P1.2, P1.3), pressing the SET key briefly will only display OP and corresponding time;

If there are OP, CL, LOP in the mode (such as mode P3.1, P3.2), short pressing the SE key will display OP and corresponding time, CL and corresponding time, LOP and corresponding number of times;

After setting the mode, you can easily view the parameters set in the current mode by short pressing the SET key on the main interface, which is very convenient!

How to set parameters:

1. Firstly, determine the working mode of the relay;

2. According to the working mode of the relay, the current working mode (default P1.1 mode) will flash on the main interface (when the module is powered on), and then enter the main interface. "Press and hold the SET button for 2 seconds and then release it" to enter the mode selection interface. Short press the UP and DOWN buttons to select the mode to be set (P1.1~P-4);

3. After selecting the mode to be set (e.g. P3.2), press the SET key briefly to set the corresponding parameters. The parameters to be set will flash (OP conduction time, CL disconnection time, LOP cycle times ("-" represents infinite cycles)). Adjust the parameter values through UP and DOWN, and support long press (fast increase or decrease) and short press (increase or decrease by 1 unit); After setting the parameter values, short press the STOP key to select the decimal point position: choose the timing range (corresponding time from 0.1 seconds to 999 minutes); Short press the SET key to set the next parameter for the current mode, the process is the same as above;

4. After setting the parameters for the selected mode, press and hold the SET button for 2 seconds before releasing it. The currently set mode will flash and then return to the main interface. Setting the parameters is successful, very simple!

Main interface: When the relay is not working, it displays "000" (without a decimal point). When the relay is working, it has a decimal point, which is very clear!

Mode selection interface: Press and hold the SET button to enter. After setting is complete, press and hold the SET button to exit and return to the main interface. The STOP button function is extended!

Parameter saving settings: First, set the state to be turned on and off. Long press SET to enter the settings, press UP, and then press DOWN.

Relay enable mode

ON: The relay is allowed to conduct during the OP conduction time

OFF: The relay is prohibited from conducting and always in a closed state

Short press the STOP button on the main interface to switch between ON and OFF. The current state will flash, and then return to the main interface. (This function is an emergency stop function, a relay that can be opened and closed with one click)

Sleep mode

1. C-P sleep mode: Within five minutes, if there is no operation, the digital display will automatically turn off and the program will run normally;

2. 0-d Normal Mode: The digital display is always on;

Press and hold the STOP button for 2 seconds, then release it to switch between C-P and 0-d states. The current state will flash, and then return to the main interface.

P1: After the signal is triggered, the relay conducts for OP time and then disconnects; During the OP time, perform the following operations

P1.1: Signal triggered again is invalid

P1.2: Signal triggered again, re timed

P1.3: Signal triggers reset again, relay disconnects, and timing stops;

P-2: Give a trigger signal, after the relay disconnects the CL time, the relay conducts the OP time, and after the timing is completed, disconnect the relay;

P3.1: Give a trigger signal, after the relay conducts OP time, the relay disconnects CL time, and then repeat the above actions. If the signal is given again within the cycle, the relay disconnects and stops timing; The number of loops (LOP) can be set;

P3.2: After power on, there is no need to trigger a signal. The relay conducts for OP time and cycles the above actions when the relay disconnects CL; The number of loops (LOP) can be set as follows:

P-4: If there is a trigger signal for the signal holding function, the timer will be reset and the relay will remain conductive. When the signal disappears, the relay will be disconnected after timing OP; During the timing period, if there is a signal again, the timing will be reset to zero;

Product Size

Product Show

Payment&Transportation

Official Certificate&Certificate

Multiple product supply

Company office environment

Warehouse Real Shot

Standard packaging

We also provide ：